Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

Coating Inspector Level 1, in Drawings Every Check in the Same Order

Dew point, surface prep grades, profile in mils, soluble salts, wet and dry film thickness, adhesion, holiday testing and the defects you'll be asked to name. Each topic gets its own page: the drawing first, then what you need to remember. 77 illustrated pages.

SHOW ME THE DRAWN PAGES

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEach check drawn, with the explanation right beside it
77 illustrated pages9 parts, from the inspector's job to the daily report and review
Up-to-date sourcesSSPC/AMPP surface prep standards, SSPC-PA 2 and ASTM test methods
PDF by emailFormat

Look Inside the Book

Every page has one big drawing and a box with the numbers, grades and steps you need to know:

Applicator vs. inspector: 4 verbs that define the inspector's job
Applicator vs. inspector: 4 verbs that define the inspector's job
Anode, cathode, electrolyte, metallic path: one water droplet shows the whole corrosion cell.
Anode, cathode, electrolyte, metallic path: one water droplet shows the whole corrosion cell.
Steel at or below the dew point gets a water film, visible or not.
Steel at or below the dew point gets a water film, visible or not.
SP 1 removes oil and grease, never rust or mill scale, and always goes first.
SP 1 removes oil and grease, never rust or mill scale, and always goes first.
Product, color, both batch numbers, expiry and storage temperature: checked and written down first.
Product, color, both batch numbers, expiry and storage temperature: checked and written down first.
Verify with certified standards or shims at shift start and end
Verify with certified standards or shims at shift start and end
Wet sponge holiday test: 9–90 V DC, films up to 20 mils, voltage per spec
Wet sponge holiday test: 9–90 V DC, films up to 20 mils, voltage per spec
Run, sag, curtain: three sizes of the same problem, too much wet film.
Run, sag, curtain: three sizes of the same problem, too much wet film.

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 9 parts and 72 topics.

The Problem Isn't You. It's How It Was Explained.

It's early morning on the blast deck. The steel looks dry, the air feels damp, and the instructor asks one question: can we start coating or not?

You read the dew point chapter. But the manual gives it to you in paragraphs: relative humidity, wet bulb, dry bulb, a chart, a rule. Standing there, the pieces don't connect.

Steel at or below the dew point gets a water film, visible or not.

In the book, dew point is one drawing: a steel plate, a thermometer and a line. Steel at or below the dew point gets a water film, visible or not. The 5 °F margin is right there in the picture.

Same with the sling psychrometer, solvent cleaning before blasting, the wet film comb, tape adhesion and runs and sags: each one has its own page.

You read the steel temperature, compare it with the dew point and make the call without going back to the manual.

COMPARE FOR YOURSELF

The Same Topic, Two Ways to Study It

THIS
  • The manual: line after line of text
  • Corrosion cells explained only in words
  • You walk into the course with doubts
Electrochemical corrosion of steel requires the simultaneous presence of four elements, which together constitute a corrosion cell. At the anodic site, iron atoms undergo oxidation, releasing electrons and entering solution as ferrous ions. These electrons travel through the metallic path to the cathodic site, where a reduction reaction consumes them, typically involving dissolved oxygen and water. The electrolyte, generally moisture containing dissolved salts, completes the circuit by permitting ionic current flow. Interruption of any single element arrests the process, which is the underlying principle of protective coating systems.
FOR THIS
  • The corrosion cell in one drawing
  • The 4 parts in a box
  • You see it and you get it
Anode, cathode, electrolyte, metallic path: one water droplet shows the whole corrosion cell.
CONTENTS

Take a Look at the 9 Parts and 72 Topics

The inspector's job, corrosion and coatings, the weather, the surface, mixing and application, wet and dry film, adhesion, holidays and cure, defects, and concrete and records: 77 pages, all illustrated

IThe Inspector's Job · pp. 6-11
  1. From Applicator to Inspector: What Changes
  2. The Spec, the Data Sheet and Who Wins
  3. The Inspection Timeline: 7 Checkpoints
  4. Your Kit Bag, Instrument by Instrument
  5. Calibration vs. Verification
  6. Safety Before Any Reading
IIWhy Steel Rusts and How Coatings Stop It · pp. 12-16
  1. The Corrosion Cell in 4 Parts
  2. 3 Ways a Coating Protects
  3. How Coatings Cure: 5 Mechanisms
  4. Generic Coating Types at a Glance
  5. The Coating System: Primer, Intermediate, Topcoat
IIICheckpoint 1: The Weather · pp. 17-23
  1. Dew Point in One Drawing
  2. The Sling Psychrometer, Step by Step
  3. From Wet Bulb to Dew Point
  4. The 5 °F Rule
  5. Steel Temperature: Where You Measure Matters
  6. Relative Humidity and Data Sheet Limits
  7. When and How Often to Take Readings
IVCheckpoint 2: The Surface · pp. 24-37
  1. Solvent Cleaning First: SP 1
  2. Initial Rust Grades A, B, C, D
  3. Hand and Power Tool Cleaning: SP 2, SP 3, SP 15, SP 11
  4. The Blast Grades Ladder
  5. Using the Visual Guides Without Fooling Yourself
  6. Waterjetting Grades WJ-1 to WJ-4
  7. Flash Rust: Light, Medium, Heavy
  8. Abrasive and Air: The Blotter and Vial Tests
  9. What Surface Profile Is
  10. Measuring Profile: Comparator, Depth Gauge, Replica Tape
  11. Replica Tape, Done Right
  12. Soluble Salts: The Invisible Contaminant
  13. The Bresle Patch Test in 5 Steps
  14. Dust on the Surface: The Tape Test
VCheckpoint 3: Mixing and Application · pp. 38-44
  1. Before You Open the Can
  2. Mixing Two-Part Coatings
  3. Pot Life and Thinning
  4. Application Methods at a Glance
  5. Reading an Airless Tip Number
  6. Stripe Coating Edges and Welds
  7. Recoat Windows
VICheckpoints 4 and 5: Wet and Dry Film · pp. 45-55
  1. The Wet Film Comb
  2. Volume Solids: Wet Becomes Dry
  3. Target WFT With Thinner Added
  4. Theoretical Coverage: The 1,604 Number
  5. DFT Gauges: Type 1 and Type 2
  6. Verifying the Gauge Before You Read
  7. Gauge Reading, Spot, Area
  8. How Many Areas to Measure
  9. The 80/120 Rule for Spots
  10. Working Out a DFT Spot Average
  11. Measuring Each Coat vs. the Whole System
VIICheckpoint 6: Adhesion, Holidays and Cure · pp. 56-61
  1. Tape Adhesion: X-Cut or Cross-Hatch
  2. Pull-Off Adhesion
  3. Holidays and Why They Matter
  4. Low-Voltage Wet Sponge
  5. High-Voltage Spark Testing
  6. Is It Cured? MEK Rub and Hardness
VIIIDefects You'll Be Asked to Name · pp. 62-70
  1. Runs, Sags and Curtains
  2. Dry Spray and Overspray
  3. Orange Peel
  4. Pinholes, Fish Eyes and Craters
  5. Blistering
  6. Mudcracking and Cracking
  7. Amine Blush
  8. Lifting, Wrinkling and Delamination
  9. Undercutting and Rust Creep
IXConcrete, Records and Review · pp. 71-77
  1. Coating Concrete: Surface Prep and Profile
  2. Moisture in Concrete: 3 Tests
  3. The Daily Inspection Report
  4. Writing a Nonconformance
  5. The Whole Job on One Page
  6. Numbers to Have at Hand
  7. Most Common Inspector Mistakes

One Page, One Topic, All Clear

Think of it this way:

It's the practical session. The instructor hands you a wet film comb and a freshly sprayed panel and asks for the reading. You have a few seconds.

In the book you open the wet film comb page and see it drawn: the comb pressed in square, the wet teeth, the dry teeth, and the reading between the last wet tooth and the first dry one.

Product, color, both batch numbers, expiry and storage temperature: checked and written down first.

Same with dew point, the blast grades ladder, replica tape, the Bresle patch test and the 80/120 rule for DFT spots: each one on its own page.

Coating Inspector Level 1 Illustrated is 9 parts and 72 topics, all drawn, with the numbers to have at hand and the most common inspector mistakes at the end.

What you see drawn, you don't have to memorize.

What's Inside Coating Inspector Level 1 Illustrated:

Ipp. 6-11

The Inspector's Job

What changes from applicator to inspector, the spec vs. the data sheet, the 7-checkpoint timeline, your inspection kit, calibration vs. verification and safety first

IIpp. 12-16

Why Steel Rusts and How Coatings Stop It

The corrosion cell in 4 parts, the 3 ways a coating protects, the 5 cure mechanisms, generic coating types and the primer-intermediate-topcoat system

IIIpp. 17-23

Checkpoint 1: The Weather

Dew point in one drawing, the sling psychrometer, wet bulb to dew point, the 5 °F rule, steel temperature, humidity limits and how often to take readings

IVpp. 24-37

Checkpoint 2: The Surface

Solvent cleaning first, rust grades A to D, hand and power tool grades, the blast grades ladder, visual guides, waterjetting, flash rust, blotter test, profile, replica tape, soluble salts, Bresle patch and the dust tape test

Vpp. 38-44

Checkpoint 3: Mixing and Application

Checks before opening the can, mixing two-part coatings, pot life and thinning, application methods, airless tip numbers, stripe coating and recoat windows

VIpp. 45-55

Checkpoints 4 and 5: Wet and Dry Film

The wet film comb, volume solids, target WFT with thinner, theoretical coverage, Type 1 and Type 2 gauges, gauge verification, reading-spot-area, how many areas, the 80/120 rule and spot averages

VIIpp. 56-61

Checkpoint 6: Adhesion, Holidays and Cure

Tape adhesion with X-cut or cross-hatch, pull-off adhesion, holidays, low-voltage wet sponge, high-voltage spark testing and cure checks with MEK rub and hardness

VIIIpp. 62-70

Defects You'll Be Asked to Name

Runs and sags, dry spray, orange peel, pinholes and fish eyes, blistering, mudcracking, amine blush, lifting and delamination, and undercutting

IXpp. 71-77

Concrete, Records and Review

Concrete prep and profile, 3 moisture tests, the daily report, writing a nonconformance, the whole job on one page, numbers to have at hand and the most common mistakes

At the end of the book: The whole job on one page, the numbers to have at hand and the most common inspector mistakes.

Plus: 2 Free Books

Coating Inspector Exam-Style Practice Questions

BONUS 1: «Coating Inspector Exam-Style Practice Questions»

Value on its own: US$ 17.90

Practice questions in the style of the theory exam, each with the answer and the page to go back to, so you find your weak spots before the course does.

15 Common Inspection Mistakes: Quick-Reference Cards

BONUS 2: «15 Common Inspection Mistakes: Quick-Reference Cards»

Value on its own: US$ 14.90

The most frequent mistakes on site and in class, drawn before and after on printable cards you can keep in your kit bag.

Coating Inspector Level 1 Illustrated with 2 Free Books

  • Coating Inspector Level 1 Illustrated: 77 illustrated pagesUS$ 63
  • BONUS 1: Coating Inspector Exam-Style Practice QuestionsUS$ 17.90
  • BONUS 2: 15 Common Inspection Mistakes: Quick-Reference CardsUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT COATING INSPECTOR LEVEL 1 ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Coating Inspector Level 1 Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You're signed up for Level 1

You're signed up for Level 1

You get the whole course in order before day one: what gets measured, with which instrument and in what sequence.

Your course week is close

Your course week is close

You review dew point, DFT averages and adhesion ratings one page at a time, and the practice questions show you where to go back.

You already inspect on the job

You already inspect on the job

You print the pages you need and keep them in your gear bag: the 5 °F rule, the wet film comb, the defects drawn.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT COATING INSPECTOR LEVEL 1 ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Coating Inspector Level 1 Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've been painting or blasting steel for years?

Yes. It doesn't teach you how to hold a spray gun: it puts the standards, grades and numbers in order for someone who already knows the work. US units throughout: mils and °F.

Where does the content come from?

It's checked against the current editions of the standards used in Level 1 coating inspector training in the US: the joint SSPC/AMPP surface prep standards, the SSPC visual guides, SSPC-PA 2 for DFT and the ASTM test methods. Everything is explained in our own words and drawings.

Is this official course material? Do I get a certificate?

No. It's an independent illustrated study book, not affiliated with or endorsed by any certifying body. It doesn't give you a certificate or course credit: certification comes only from your course and its exams.

Does it replace the course?

No. It helps you arrive prepared and review afterwards. The course, the hands-on training and the project spec always come first.

Are the practice questions the ones on the exam?

No. They're written for this book, in the style of a theory exam, each with the answer and the page to go back to.

When and how do I get it?

The book and the 2 bonus books come as PDFs by email, to the address you enter at checkout.

Do I have to pay every month?

No. It's a one-time payment.

Can I have it on paper?

Yes. The PDF is made to print: print the whole book or just the pages you want in your gear bag.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading that doesn't stick.

Dew point, profile and DFT: you see them drawn, and that's it.

You walk into the course knowing where everything is.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT COATING INSPECTOR LEVEL 1 ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.